Showing posts with label pickit 2. Show all posts
Showing posts with label pickit 2. Show all posts

Saturday, August 24, 2013

EagleUp Model Files

Eagle Up stepstick A4988 Model
EagleUp stepstick A4988

                                                                       TI launchpad Model
EagleUp TI launchpad

                                                                         Pickit 2 Model 
EagleUp Pickit 2
                           
                                                                     RTC Model
EagleUp RTC breakout board

                                                                           GSM Model
EagleUp GPS breakout board

                                                                 Ultrasonic Model
EagleUp Ultrasonic breakout board

                                                                 Uno32 Model
EagleUp Uno 32

                                                                 Microchip Wifi Module Model
EagleUp wifi breakout board

                                                                   Ethernet Module Model
EagleUp ethernet breakout board


Sunday, July 3, 2011

Troubleshooting Pickit 2 Clone

Pickit 2 is a multipurpose tool : PIC programmer, debugger, UART and Logic analyzer provided by Microchip and the schematics is provided in Pickit 2 datasheet.

Schematics:



Specifications:



  1. Easy to use Windows® programming interface for programming Microchip's Flash family of microcontrollers

  2. UART Tool software for direct serial communications with a microcontroller RX/TX pins through the PICkit 2.

  3. Logic Tool software for simple logic signal stimulus and monitoring, with a 3-channel logic analyzer.

  4. PICkit 2 Programmer-To-Go support for programming devices without a PC.

  5. Code Examples in assembly and C.


Test methods:


Hardware – based:



  1. Ensure that PIC18F4550 is programmed.

  2. The VPP generated voltage should be about 11V to 13V while VDD is 5V.

  3. The P MOS used need to be IRLML6402 to provide enough power to programming.


Software-based:


Pickit 2 Troubleshoot can be found in TOOLS -> TROUBLESHOOT.. After you have clicked on the button, a pop up menu as shown below will appear. Click on NEXT.


The first step of troubleshooting is to verify the VDD. For PIC18F, the VDD is 4.5V, while for PIC16F, it is about 3.6V. Click on TEST to measure the VDD. The VDD can be further verified by using a multimeter at pin 2 and pin 3 of the ICSP.


Once the TEST button is clicked,  there will be a message whether it passed the VDD test or failed. If the VDD test failed, then, it is necessary to check whether the installation of components is correct.



Assuming the VDD test has passed, we will go on to verify the VPP now. The VPP for PIC18F is about 12V. This can also be verified further using a multimeter. For PICKIT 2 clones, it is often caused by the MOSFET( BS250) which is most likely used as a substitute for IRLML6402. Here, you can also test for MLCR 'high' and 'low'.


Once the VPP test has passed, we will move on to troubleshoot the PGC and PGD using a frequency counter or frequency measurement equipment. The range of the frequency when it is toggled at 30kHZ is about 26 – 28kHz. You may also try to pull the PGC and PID pin to 'high' or 'low' and measure it with your multimeter.


After everything has been done, click on the FINISHED button. Now, you are ready to use your pickit 2.

Conclusion


Pickit 2 is a great multipurpose tool that enables you to program and debug a PIC microcontroller. In addition, it also has a UART tool, and logic analyzer.

Thursday, May 13, 2010

Pickit 2 Clone

   PICKIT 2 CLONE




   
Pickit 2 clone is a low cost homemade pickit 2 that has similar microcontroller support: baseline (PIC10F, PIC12F5xx, PIC16F5xx), midrange (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. T